| Sensaphone Web600 Accessories & Monitoring Sensors |
|
Mini Surge Protector
Power and Phone
FGD-0067 |
Surge Suppressor with modem/fax surge suppression ; The traveler surge suppressor offers complete AC and phone line surge suppression for your Sensaphone and other electronic devices. A set of RJ11 telephone line suppression jacks protect dialup and voice/modem lines. Dimensions: 3.5" x 2.5" x 1.75". More info |
|
|
Spot Water Detector
FGD-0013 |
Spot Water Detector ; Can be used with all Sensaphone models to detect the presence of water on a horizontal surface. Independently powered by internal lithium batteries. The batteries should last approximately 3 to 5 years. Multiple sensors can be wired in series to a single input. Comes with 25ft of wire. Dimensions: 2.25" x 1.125" x 3.625". More info |
|
|
Zone Water Detector
FGD-0056 |
Zone Water Detector ; For use in detecting the presence of water on a floor or in a false ceiling. Comes with 10ft of WaterRope cable to cover a larger area than the FGD-0013 water sensor. Up to three WaterRopes can be cascaded from a single sensor for even greater coverage. Works with all Sensaphone products. Operates on two AA batteries (installed). Comes with 25 feet of wire. For additional 10ft of Water Rope, see FGD-0063. More info |
|
|
Extra 10ft Water Rope
FGD-0063 |
Additional 10ft Water Rope for use with Zone Water Detector FGD-0056. |
|
|
Temp Alert
FGD-0022 |
Temp Alert ; Wall mount, mechanical temperature sensor to detect if air temperature is too high or too low. Can be used with all Sensaphone models to monitor air temperature from -30° to 130° F (-34° to 54° C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When temperature exceeds the setting, the sensor triggers an alarm. Multiple Temp Alerts may be wired in parallel to a single input. No power required for operation. Comes with hook-up wire. Dimensions : 6.25" x 3.25" x 2". More info |
|
|
Humidistat
FGD-0027 |
Humidistat ; Wall mount humidity sensor to detect if humidity is too high or too low. Can be used with all Sensaphone models. Range of the humidistat is 10% to 60% RH. The sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input. Does not come with hook-up wire.
Dimensions : 4.125" x 2.75" x 1.5". More info |
|
|
Magnetic Reed Switch
FGD-0006 |
Magnetic Reed Switch ; Detects unauthorized entry or intrusion. Usually installed on most doors and windows to detect their opening and closing. May be used with all Sensaphone models. Several magnetic reed switches may be wired in series. Does not come with hook-up wire. Dimensions : 2.5" x 0.75" x 0.5" (part with screw terminals) 2.5" x 0.75" x 0.625" (part with magnet). More info |
|
|
Infra-Red Motion Detector
FGD-0007 |
Passive Infra-Red Motion Detector ; Can be used with all Sensaphone models to monitor the movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Range of detection covers approximately 40 sq ft. Multiple sensors can be wired in series. Does not come with hook-up wire. Dimensions: 4" x 6" x 1.5". More info |
|
|
Smoke Detector 110VAC
FGD-0049 |
Smoke Detector with Built-In Relay ; This photoelectric smoke alarm is powered by a hard wired 120VAC connection and provides an alarm output to trigger a Sensaphone alarm dial out. Has two sets of dry alarm contacts, one form - A SPST, and one form - C SPDT. The detector has tandem interconnect capability, allowing up to 6 devices to be connected together. A 90dBA audible horn is included. Can be used with all Sensaphone models. Does not come with hook-up wire. Dimensions: 5.1" diameter x 2.5". More info |
|
|
Smoke Detector w/Battery Backup
FGD-0049-B |
Same smoke detector as the FGD-0049, with the addition of a battery backup so that alarms can still be detected during a power failure. Works with all Sensaphone products. Does not come with wire. |
|
|
Humidity Transmitter
FGD-0052 |
Humidity Transmitter ( 4-20mA ) ; A space-mount, low-profile humidity transducer. Transmits actual humidity levels to the Sensaphone for programmable high and low alarm limits. Can be used with any Sensaphone that supports 4-20mA inputs. The 24V power supply ( FGD-0053 ) is required unless the transmitter is used with SCADA 3000 or Express II. Does not come with hook-up wire. Dimensions: 2.75" x 4.50" x 1.38". More info |
|
|
Power Supply for FGD-0052
FGD-0053 |
Exclusively for use with the FGD-0052 Humidity Transmitter. Only required if the Sensaphone model does not provide loop power for 4-20mA circuit. |
|
|
Power-Out Alert
FGD-0054 |
Power-Out Alert Model PS-110 : A compact power outage monitoring device to detect power failures. Easily plugs into any 110 VAC receptacle outlet for operation. Works with all Sensaphone models. Comes with 15ft hook-up wire. Dimensions: 2.25" x 2" x 3". More info |
|
|
2.8K Temperature Sensor
with Glass Bead Vial
FGD-0107 |
2.8K Temperature Sensor with Glass Bead Vial ; is ideal for cold storage temperature monitoring. This is a highly recommended sensor for every cold storage application. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycle, opening of doors, and fans circulating air. Ranges: For Sensaphone 400 and 800 -20° to 150°F, For Sensaphone 1400, 1800, 2800, WEB600 : -109° to 115°F, For Sensaphone 2000 : -125° to 124°F, For Sensaphone Express II : -85° to 200°F. Does not come with wire. More info |
|
|
2.8K Temperature Sensor
FGD-0100 |
2.8K Remote Temperature Sensor ; Enables monitoring temperature at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low limits. It may be mounted anywhere air temperatures need to be measured, howeverthis model is recommended to be located in clean, dry environment. Ranges: For Sensaphone 400 and 800 -20° to 150°F, For Sensaphone 1400, 1800, 2800, WEB600 : -40° to 115°F, For Sensaphone 2000 : -40° to 124°F, For Sensaphone Express II : -40° to 150°F. Dimensions: 2.5" x .75" x .75". Does not come with wire.
For outdoor use, model FGD-0101 is recommended. More info |
|
|
2.8K Weatherproof
Temperature Sensor
FGD-0101 |
2.8K Weatherproof Remote Temperature Sensor ; Enables monitoring temperature at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low limits. It may be mounted anywhere air temperatures need to be measured, and is suitable for use in wet, dirty environments. Comes with 12ft wire. Ranges: For Sensaphone 400 and 800 -20° to 150°F, For Sensaphone 1400, 1800, 2800, WEB600 : -109° to 115°F, For Sensaphone 2000 : -125° to 124°F, For Sensaphone Express II : -85° to 200°F.
For indoor use, model FGD-0100 is recommended. More info |
|
|
2.8K Weatherproof
Temperature Sensor with NIST
FGD-0101-NIST |
2.8K Weatherproof Remote Temperature Sensor with NIST ; Same as FGD-0101, but with Traceable Calibration Certificate
(NIST Temperature Certification). |
|
|
10K Weatherproof
Temperature Sensor
FGD-0102 |
10K Weatherproof Remote Temperature Sensor ; Enables monitoring temperature at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low limits. It may be mounted anywhere air temperatures need to be measured, and is suitable for use in wet, dirty environments. Comes with 12ft wire. Ranges: For Sensaphone 1400, 1800, 2800, WEB600 : -87° to 168°F, For Sensaphone 2000 : -90° to 200°F, For Sensaphone Express II : -80° to 200°F, For SCADA 3000 : -35° to 205°F
For indoor use, model FGD-0100 is recommended. More info |
|
|
10K Immersion
Temperature Sensor
FGD-0105 |
10K Immersion Temperature Sensor : Is a waterproof temperature sensor for measuring the temperature of fluids inside a pipe. It is constructed of brass WEL-B thermowell ( which screws into a customer-supplied 0.5" NPT saddle or Thredolet fitting in a pipe). It fits into a thermowell via a brass 0.125" NPT fitting. Accurate to ± 0.36°F (0.2°C) and has a sensing range of 10°F to 230°F. Includes 8ft of 24AWG wire. Dimensions: Thermowell 5.125", Sensor in well 6.5". More info |
|
|
10K Indoor Decorator
Zone Temperature Sensor
FGD-0103 |
10K Indoor Decorator Zone Temperature Sensor : Offers precision room temperature sensing in an attractive wall-mounted enclosure. Accurate to 0.36°F (0.2°C) with a sensing range of 35°F to 140°F. The indoor decorator comes in a beige plastic enclosure, with a tan metal face plate. The cover is secured with tamper resistant hex screws. Dimensions: 4.5" x 3.25" x 1.25". Does not come with wire. More info |
|
|
10K Outdoor Air
Weatherproof
Temperature Sensor
FGD-0104 |
10K Outdoor Air Weatherproof Temperature Sensor : Is a sensitive temperature element with a stainless steel tube sheathe. It is mounted inside a ventilated, treated weather-resistant PVC shield to minimize radiant energy effects and mounted on a weatherproof outlet box for easy outdoor installation. Accurate to ± 0.36°F (0.2°C) with a sensing range of 30°F to 140°F. Comes with 8ft of 24AWG wire. Dimensions: 9" x 3" x 2". More info |
|
|
J Type Thermocouple /
4-20mA Converter
FGD-0220 |
J-Type Thermocouple / 4-20mA Converter : Allows you to use a standard J-type thermocouple on any Sensaphone that accepts a 4-20mA input signal. It is useful when monitoring very high or very low temperatures that can not be monitored with a standard Sensaphone temperature sensor. Thermocouple not included. More info |
|
|
Float Switch
FGD-0222 |
Float Switch: The FGD-0222 float switch is a plastic, side-mounted float switch that is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of a tank. This style float switch can be rotated for Normall Open or Normally Closed operation. Combine two switches at different levels for a high and low level or pump control or alarming. More info |
|
|
Multi-Point Wireless I/O
FGD-0205 |
Multi-Point Wireless I/O : Is ideal if you need to connect one or two dry contacts and/or a 4-20mA transducer to a Sensaphone that is too far or too expensive to run cable. Two 24V power supplies and omni-directional antennas are included. Built-in LEDs indicate RF link and dry contact status. More info |
|
|
Air Quality Sensor
FGD-0066 |
Indoor Air Quality Sensor: The Sensaphone Indoor Air Quality sensor will allow you to monitor levels of pollution from 0-100 percent with any Sensaphone that will accept a 4-20mA input signal. These air contaminants include cigarette smoke, cooking exhaust, automobile exhaust, solvents, and many others. This sensor requires a 24VDC power supply, part number FGD-0053. More info |
|
|
Carbon Monoxide
(CO) Sensor
FGD-0065 |
Carbon Monoxide Sensor: Carbon Monoxide is a highly toxic gas that has no color or odor. The Sensaphone Carbon Monoxide sensor will allow you to monitor CO levels from 0-300 ppm with any Sensaphone that will accept a 4-20mA input signal. This sensor requires a 24VDC power supply, part number FGD-0053. More info |
|
|
Carbon Dioxide
(CO2) Sensor
FGD-0068 |
Carbon Dioxide Sensor: The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000 ppm with any Sensaphone that will accept a 4-20mA input signal. This sensor requires a 24VDC power supply, part number FGD-0053. More info |
|
|
Sensaphone Accessories
|
Sensor Inputs: Connect up to six external sensors to monitor a variety of equipment and conditions. Each input zone can be connected to a temperature sensor, an analog transducer, or a dry contact switch. 