FGD2000 Programmable Environmental Monitor, Data Logger

FGD2000 - Essential Programmable Environmental Monitor and Data Logger

Sensaphone FGD2000 supplies the critical information needed to prevent costly problems and maintain peak performance at any kind of industrial or commercial facility. It is an essential tool for environmental monitoring and data logging in a variety of applications.

This product has been discontinued, with no direct replacement. However, the SCADA 3000 is the closest in comparison if you do not want a web based system that requires an Ethernet connection. Otherwise, the IMS-1002 with IMS sensors would be the next model to consider.

Sensaphone FGD-2000 Accessories & Monitoring Sensors
Accessory Hook-Up Wire FGD-0010	Accessory Hook-Up Wire ; 50 ft. of 22-gauge wire for connecting sensors to your Sensaphone.	$6.00 Qty

Mini Surge Protector Power and Phone FGD-0067	Surge Suppressor with modem/fax surge suppression ; The traveler surge suppressor offers complete AC and phone line surge suppression for your Sensaphone and other electronic devices. A set of RJ11 telephone line suppression jacks protect dialup and voice/modem lines. Dimensions: 3.5" x 2.5" x 1.75". More info	$17.10 Qty

Spot Water Detector FGD-0013	Spot Water Detector ; Can be used with all Sensaphone models to detect the presence of water on a horizontal surface. Independently powered by internal lithium batteries. The batteries should last approximately 3 to 5 years. Multiple sensors can be wired in series to a single input. Comes with 25ft of wire. Dimensions: 2.25" x 1.125" x 3.625". More info	$81.00 Qty

Zone Water Detector FGD-0056	Zone Water Detector ; For use in detecting the presence of water on a floor or in a false ceiling. Comes with 10ft of WaterRope cable to cover a larger area than the FGD-0013 water sensor. Up to three WaterRopes can be cascaded from a single sensor for even greater coverage. Works with all Sensaphone products. Operates on two AA batteries (installed). Comes with 25 feet of wire. For additional 10ft of Water Rope, see FGD-0063. More info	$121.50 Qty

Extra 10ft Water Rope FGD-0063	Additional 10ft Water Rope for use with Zone Water Detector FGD-0056.	$63.00 Qty

Temp Alert FGD-0022	Temp Alert ; Wall mount, mechanical temperature sensor to detect if air temperature is too high or too low. Can be used with all Sensaphone models to monitor air temperature from -30° to 130° F (-34° to 54° C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When temperature exceeds the setting, the sensor triggers an alarm. Multiple Temp Alerts may be wired in parallel to a single input. No power required for operation. Comes with hook-up wire. Dimensions : 6.25" x 3.25" x 2". More info	$58.50 Qty

Humidistat FGD-0027	Humidistat ; Wall mount humidity sensor to detect if humidity is too high or too low. Can be used with all Sensaphone models. Range of the humidistat is 10% to 60% RH. The sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input. Does not come with hook-up wire. Dimensions : 4.125" x 2.75" x 1.5". More info	$36.00 Qty

Magnetic Reed Switch FGD-0006	Magnetic Reed Switch ; Detects unauthorized entry or intrusion. Usually installed on most doors and windows to detect their opening and closing. May be used with all Sensaphone models. Several magnetic reed switches may be wired in series. Does not come with hook-up wire. Dimensions : 2.5" x 0.75" x 0.5" (part with screw terminals) 2.5" x 0.75" x 0.625" (part with magnet). More info	$9.00 Qty

Infra-Red Motion Detector FGD-0007	Passive Infra-Red Motion Detector ; Can be used with all Sensaphone models to monitor the movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Range of detection covers approximately 40 sq ft. Multiple sensors can be wired in series. Does not come with hook-up wire. Dimensions: 4" x 6" x 1.5". More info	$71.10 Qty

Smoke Detector 110VAC FGD-0049	Smoke Detector with Built-In Relay ; This photoelectric smoke alarm is powered by a hard wired 120VAC connection and provides an alarm output to trigger a Sensaphone alarm dial out. Has two sets of dry alarm contacts, one form - A SPST, and one form - C SPDT. The detector has tandem interconnect capability, allowing up to 6 devices to be connected together. A 90dBA audible horn is included. Can be used with all Sensaphone models. Does not come with hook-up wire. Dimensions: 5.1" diameter x 2.5". More info	$49.50 Qty

Smoke Detector w/Battery Backup FGD-0049-B	Same smoke detector as the FGD-0049, with the addition of a battery backup so that alarms can still be detected during a power failure. Works with all Sensaphone products. Does not come with wire.	$58.50 Qty

Humidity Transmitter FGD-0052	Humidity Transmitter ( 4-20mA ) ; A space-mount, low-profile humidity transducer. Transmits actual humidity levels to the Sensaphone for programmable high and low alarm limits. Can be used with any Sensaphone that supports 4-20mA inputs. The 24V power supply ( FGD-0053 ) is required unless the transmitter is used with SCADA 3000 or Express II. Does not come with hook-up wire. Dimensions: 2.75" x 4.50" x 1.38". More info	$224.10 Qty

Power Supply for FGD-0052 FGD-0053	Exclusively for use with the FGD-0052 Humidity Transmitter. Only required if the Sensaphone model does not provide loop power for 4-20mA circuit.	$41.39 Qty

Power-Out Alert FGD-0054	Power-Out Alert Model PS-110 : A compact power outage monitoring device to detect power failures. Easily plugs into any 110 VAC receptacle outlet for operation. Works with all Sensaphone models. Comes with 15ft hook-up wire. Dimensions: 2.25" x 2" x 3". More info	$53.10 Qty

2.8K Temperature Sensor with Glass Bead Vial FGD-0107	2.8K Temperature Sensor with Glass Bead Vial ; is ideal for cold storage temperature monitoring. This is a highly recommended sensor for every cold storage application. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycle, opening of doors, and fans circulating air. Ranges: For Sensaphone 400 and 800 -20° to 150°F, For Sensaphone 1400, 1800, 2800, WEB600 : -109° to 115°F, For Sensaphone 2000 : -125° to 124°F, For Sensaphone Express II : -85° to 200°F. Does not come with wire. More info	$49.50 Qty

2.8K Temperature Sensor FGD-0100	2.8K Remote Temperature Sensor ; Enables monitoring temperature at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low limits. It may be mounted anywhere air temperatures need to be measured, howeverthis model is recommended to be located in clean, dry environment. Ranges: For Sensaphone 400 and 800 -20° to 150°F, For Sensaphone 1400, 1800, 2800, WEB600 : -40° to 115°F, For Sensaphone 2000 : -40° to 124°F, For Sensaphone Express II : -40° to 150°F. Dimensions: 2.5" x .75" x .75". Does not come with wire. For outdoor use, model FGD-0101 is recommended. More info	$18.00 Qty

2.8K Weatherproof Temperature Sensor FGD-0101	2.8K Weatherproof Remote Temperature Sensor ; Enables monitoring temperature at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low limits. It may be mounted anywhere air temperatures need to be measured, and is suitable for use in wet, dirty environments. Comes with 12ft wire. Ranges: For Sensaphone 400 and 800 -20° to 150°F, For Sensaphone 1400, 1800, 2800, WEB600 : -109° to 115°F, For Sensaphone 2000 : -125° to 124°F, For Sensaphone Express II : -85° to 200°F. For indoor use, model FGD-0100 is recommended. More info	$27.00 Qty

2.8K Weatherproof Temperature Sensor with NIST FGD-0101-NIST	2.8K Weatherproof Remote Temperature Sensor with NIST ; Same as FGD-0101, but with Traceable Calibration Certificate (NIST Temperature Certification).	$117.00 Qty

10K Weatherproof Temperature Sensor FGD-0102	10K Weatherproof Remote Temperature Sensor ; Enables monitoring temperature at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low limits. It may be mounted anywhere air temperatures need to be measured, and is suitable for use in wet, dirty environments. Comes with 12ft wire. Ranges: For Sensaphone 1400, 1800, 2800, WEB600 : -87° to 168°F, For Sensaphone 2000 : -90° to 200°F, For Sensaphone Express II : -80° to 200°F, For SCADA 3000 : -35° to 205°F For indoor use, model FGD-0100 is recommended. More info	$27.00 Qty

10K Immersion Temperature Sensor FGD-0105	10K Immersion Temperature Sensor : Is a waterproof temperature sensor for measuring the temperature of fluids inside a pipe. It is constructed of brass WEL-B thermowell ( which screws into a customer-supplied 0.5" NPT saddle or Thredolet fitting in a pipe). It fits into a thermowell via a brass 0.125" NPT fitting. Accurate to ± 0.36°F (0.2°C) and has a sensing range of 10°F to 230°F. Includes 8ft of 24AWG wire. Dimensions: Thermowell 5.125", Sensor in well 6.5". More info	$54.00 Qty

10K Indoor Decorator Zone Temperature Sensor FGD-0103	10K Indoor Decorator Zone Temperature Sensor : Offers precision room temperature sensing in an attractive wall-mounted enclosure. Accurate to 0.36°F (0.2°C) with a sensing range of 35°F to 140°F. The indoor decorator comes in a beige plastic enclosure, with a tan metal face plate. The cover is secured with tamper resistant hex screws. Dimensions: 4.5" x 3.25" x 1.25". Does not come with wire. More info	$36.00 Qty

10K Outdoor Air Weatherproof Temperature Sensor FGD-0104	10K Outdoor Air Weatherproof Temperature Sensor : Is a sensitive temperature element with a stainless steel tube sheathe. It is mounted inside a ventilated, treated weather-resistant PVC shield to minimize radiant energy effects and mounted on a weatherproof outlet box for easy outdoor installation. Accurate to ± 0.36°F (0.2°C) with a sensing range of 30°F to 140°F. Comes with 8ft of 24AWG wire. Dimensions: 9" x 3" x 2". More info	$63.00 Qty

J Type Thermocouple / 4-20mA Converter FGD-0220	J-Type Thermocouple / 4-20mA Converter : Allows you to use a standard J-type thermocouple on any Sensaphone that accepts a 4-20mA input signal. It is useful when monitoring very high or very low temperatures that can not be monitored with a standard Sensaphone temperature sensor. Thermocouple not included. More info	$314.10 Qty

Float Switch FGD-0222	Float Switch: The FGD-0222 float switch is a plastic, side-mounted float switch that is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of a tank. This style float switch can be rotated for Normall Open or Normally Closed operation. Combine two switches at different levels for a high and low level or pump control or alarming. More info	$35.10 Qty

Multi-Point Wireless I/O FGD-0205	Multi-Point Wireless I/O : Is ideal if you need to connect one or two dry contacts and/or a 4-20mA transducer to a Sensaphone that is too far or too expensive to run cable. Two 24V power supplies and omni-directional antennas are included. Built-in LEDs indicate RF link and dry contact status. More info	$1125.00 Qty

Serial to Ethernet Device Server FGD-0300	Serial-To-Ethernet Device Server: The Serial-to-Ethernet Device Server allows you to access your Sensaphone 2000 or SCADA 3000 anywhere on a local LAN or the internet. Simply connect the device to the serial poer on your Sensaphone and connect the Ethernet jack to your network. The software included with the device server will route your computer's serial port to the network-connected device server, thus establishing a fast, direct connection to your Sensaphone. More info	$179.10 Qty

Air Quality Sensor FGD-0066	Indoor Air Quality Sensor: The Sensaphone Indoor Air Quality sensor will allow you to monitor levels of pollution from 0-100 percent with any Sensaphone that will accept a 4-20mA input signal. These air contaminants include cigarette smoke, cooking exhaust, automobile exhaust, solvents, and many others. This sensor requires a 24VDC power supply, part number FGD-0053. More info	$134.10 Qty

Carbon Monoxide (CO) Sensor FGD-0065	Carbon Monoxide Sensor: Carbon Monoxide is a highly toxic gas that has no color or odor. The Sensaphone Carbon Monoxide sensor will allow you to monitor CO levels from 0-300 ppm with any Sensaphone that will accept a 4-20mA input signal. This sensor requires a 24VDC power supply, part number FGD-0053. More info	$197.10 Qty

Carbon Dioxide (CO2) Sensor FGD-0068	Carbon Dioxide Sensor: The Sensaphone Carbon Dioxide sensor will allow you to monitor levels of Carbon Dioxide from 0-2,000 ppm with any Sensaphone that will accept a 4-20mA input signal. This sensor requires a 24VDC power supply, part number FGD-0053. More info	$206.10 Qty

Dialing Parameters	• Programmable call list for each input. • Call progress monitoring: detect dial tone, busy signals & ringback. • Programmable time between calls: 10 seconds to 60 minutes.
Destinations	• 32 destinations. • 36-digit phone numbers, 64 character email addresses. • Programmable 24x7 call schedule for each destination.
Inputs	• 8 Universal Inputs & 1 AC Power. • Normally Open/Normally Closed dry contact, Pulse Count, Run Time Accumulator. • Complete with 2.8K or 10K thermistors. • 4-20mA current loop, or 0-5V DC analog. • 10 bit resolution.
Communication Methods	Programmable Voice, fax, Cell Phone / Alpha Pager Text Message, Numeric Pager, E-mail, Web page.
Custom Voice Messages	8 Input messages (4 seconds each), 1 site ID message (6 seconds).
Data Logging	• 32,000 records, each with time and date stamp. • Selectable logging interval: 1 second to 200 hour. • Select channels to log: Inputs 1-8, AC Power, Backup Battery Voltage.
Communication Ports	• RS-232 port for local programming. • DB25 female DCE. • 38,400 bps.
Built-in Fax/Modem	• Data throughput 14,400 bps. • 14,400 bps Fax. • Protocols: V.32bis, V.32, V.22bis, V.22A/B, V.23, V.21, Bell 212A & 103.
Local LED Indicators	• Inputs 1 - 8 Alarm Status. • Power Alarm. • Phone. • Battery OK.
Power Requirements	• External transformer 120VAC 60Hz 10W (UL-listed power supply). • (6) C-cell Rechargeable Ni-Cad batteries (not included). • 10 hour battery backup.
Operating Temperature Range	0 - 50� C (32-122� F).
Humidity Range	0 - 90% RH, non-condensing.
Size	12.1"w x 7.2"h x 1.6"d.